Máy in epson n2500 lỗi paper set lc1 a4 năm 2024

The paper size setting is different from the size of paper loaded in the printer. Check to see if the correct size of paper is loaded in the specified paper source.

To clear this error, select Clear Warning from the control panel's Reset Menu. See for instructions.

Check Paper Type

The media loaded in the printer does not match the paper type setting in the printer driver. Media that matches only the paper size setting will be used for printing.

To clear this error, select Clear Warning from the control panel's Reset Menu. See for instructions.

Collate disabled

Printing by specifying the number of copies is no longer possible due to a lack of memory (RAM) or free disk space on the optional Hard Disk Drive. If this error occurs, print only one copy at a time.

To clear this error, select Clear Warning from the control panel's Reset Menu. See for instructions.

Cooling Down

The printer lowers its temperature to optimize for the fixing toner. Wait for a moment for Ready to appear in the LCD panel.

DM Error 001

The Duplex Unit has become separated from the printer. Turn the printer off, reinstall the Duplex Unit and turn the printer on again.

Duplex Mem Overflow

There is not enough memory for duplex printing. The printer prints only on the front and ejects the paper. To clear this error, follow the instructions below.

If Off is selected as the Auto Cont setting on the control panel's Setup Menu, press the Start/Stop button to print on the back of the next sheet, or press the Cancel Job button to cancel the print job.

If On is selected as the Auto Cont setting on the control panel's Setup Menu, printing continues automatically after a certain period of time.

Duplex Unit Open

The Duplex Unit's cover is open.

Form Feed

The printer is ejecting paper due to a user request. This message appears when pressing the Start/Stop button once to make the printer offline, and then holding down the Start/Stop button for more than 2 seconds in order not to receive form feed command.

Image Cart ID Error

The wrong imaging cartridge has been installed. Replace it with the correct imaging cartridge for this printer. See for instructions.

Image Optimum

There is insufficient memory to print the page at the specified print quality. The printer automatically lowers the print quality so that it can continue printing. If the quality of the printout is not acceptable, try simplifying the page by limiting the number of graphics or reducing the number and size of fonts.

To clear this error, select Clear Warning from the control panel's Reset Menu. See for instructions.

Turn the Image Optimum setting off on the control panel's Printing Menu if you do not want the printer to automatically lower the print quality to continue printing.

You may need to increase the amount of printer memory to be able to print at the desired print quality for your document. For more information on adding memory, see .

Install Imaging Cart

The imaging cartridge is not installed or not installed correctly. Make sure that the imaging cartridge is installed correctly.

Invalid AUX I/F Card

This message means that the printer cannot communicate with the installed optional interface card. Turn off the printer, remove the card, then reinstall it.

Invalid PS3

An optional PostScript 3 ROM module that cannot be used on this printer is installed. Turn off the printer and remove the module.

Invalid ROM A

The printer cannot read the installed optional ROM module. Turn off the printer and remove the ROM module.

Jam XXX

The location where the paper jam occurred is displayed at xxx. xxx indicates the location of the error.

If a paper jam occurs at two or more locations simultaneously, the corresponding multiple locations are displayed.

Jam A

Paper is jammed at the Cover A. For instructions on how to remove jammed paper at the Cover A, see .

Jam A B

Paper is jammed inside the output path cover (cover A or B) or fuser unit. For instructions on how to remove jammed paper at the output path cover or fuser unit, see .

Jam MP A Jam C1 A Jam C2 A Jam C3 A

Paper is jammed inside the optional lower cassette. For instructions on how to remove jammed paper in the optional lower cassette, see .

Jam DM

Paper is jammed inside the optional Duplex Unit's paper path or cover (cover DM). For instructions on how to remove jammed paper at the Duplex Unit, see .

Manual Feed xxx

The manual feed mode is specified for the current print job. Make sure the paper size indicated by xxx is loaded, then press the Start/Stop button.

If you do not want to print this job in manual mode, press the Cancel Job button.

For details on the manual feed mode, see .

Mem Overflow

The printer has insufficient memory to execute the current task. Press the Start/Stop button on the control panel to resume printing. Or press the Cancel Job button to cancel the print job.

Need Memory

The printer has insufficient memory to complete the current print job. Cancel printing by deleting it from the print queue on your computer, or by pressing the Cancel Job button on the printer.

To clear this error message, select Clear Warning from the control panel's Reset Menu. See for instructions.

To prevent this problem from happening again, add more memory to your printer as described in .

Offline

The printer is not ready to print. Press the Start/Stop button.

Optional RAM Error

The optional memory module may be corrupted or incorrect. Replace it with a new one.

Paper Out XXXXX YYYY

There is no paper in the specified paper source (XXXXX). Load paper of the indicated size (YYYY) into the paper source.

Paper Set XXXXX YYYY

The paper loaded in the specified paper source (XXXXX) does not match the required paper size (YYYY). Replace the loaded paper with the correct size paper and press the Start/Stop button to resume printing. Or press the Cancel Job button to cancel the print job.

If you press the Start/Stop button without replacing the paper, the printer will print on the loaded paper even though it does not match the required size.

Printer Open

One or more of the following covers are open; Cover A or Cover B.

Print Overrun

The required time to process the print data exceeded the print engine speed because the current page is too complex. Press the Start/Stop button to resume printing. Or press the Cancel Job button to cancel the print job. If this message appears again, select On as the Page Protect setting in the control panel's Setup Menu.

If you continue to receive this message when printing a particular page, try simplifying the page by limiting the number of graphics or reducing the number and size of fonts.

You can also add more memory to the printer as described in .

RAM Check

The printer is checking the RAM.

Ready

The printer is ready to receive data and print.

Replace Toner

The toner has run out.

Install a new imaging cartridge. See for instructions.

This error is not displayed when the Toner Out setting is set to Continue in the control panel setting. When the Toner Out setting is set to Continue, replace the imaging cartridge if the printout is light or faint.

Reset

The printer's current interface has been reset and the buffer has been cleared. However, other interfaces are still active and retain their settings and data.

Reset All

All printer settings have been reset to the default configuration, or to the last settings that were saved.

Reset to Save

A control panel menu setting was changed while the printer was printing. Press the Start/Stop button to clear this message. The setting will become effective after printing has finished.

ROM Check

The printer is checking the ROM.

Self Test

The printer is performing a quick internal check.

Service Req xyyyy

A controller error or a print engine error has been detected. Turn off the printer. Wait at least 5 seconds and then turn it back on. If the error message still appears, write down the error number listed on the LCD panel (xyyyy) and turn off the printer, unplug the power cord, and contact a qualified service representative.

Sleep

The printer is in sleep mode.

Toner Low

The imaging cartridge is running out of toner. If the printout is too light or faint, replace the imaging cartridge as described in .

You can continue to print until the Replace Toner error message appears. Waiting until this message appears before replacing the toner is recommended as toner may spill during replacement if toner remains in the cartridge. When printouts become faint, see for instructions.

To clear this error, select Clear Warning from the control panel's Reset Menu. See for instructions.

Turn Paper XX

The direction of the paper loaded in the specified paper source (XX) does not match the required paper direction. Turn the paper direction to landscape.

Unable Clear Error

The printer cannot clear an error message because the error status still remains. Try solving the problem again.

Warming Up

The printer is warming up.

Write Error ROM A/Write Error ROM P

This message indicates an internal error in the printer. Reset the printer. If this error persists, consult your dealer.

Writing ROM A/Writing ROM P

This message indicates that a ROM module in slot is being written. Please wait until this message disappears.